Page 1 of 2

Chamfer and Fillet

Posted: Thu Jan 07, 2021 3:56 pm
by debenriver
Hi Eric

Is it possible to improve the directional action of chamfer and fillet??

For example, as shown below, if I drag from A to B, I get a fillet from C to B:
Screenshot 2021-01-07 at 11.07.21.png
Screenshot 2021-01-07 at 11.07.21.png (25.21 KiB) Viewed 5465 times
In this example, of the four options, only a drag from B to C or A to D produces a fillet where I want it

The only way to ensure that the fillet is where I drag is to cut the two lines first like this and then I get the filet where I want it:
Screenshot 2021-01-07 at 10.51.12.png
Screenshot 2021-01-07 at 10.51.12.png (16.41 KiB) Viewed 5465 times
It's the same for chamfers.

I realize it's to do with the directions the lines are drawn in – so in the example, if I drew the lines from left to right and top to bottom, the dragging A to B produces a fillet from A to B – and B to C produces a fillet from B to C but the other two options don't work!

I don't remember this being a problem in earlier versions????

Cheers -- George

Re: Chamfer and Fillet

Posted: Fri Jan 08, 2021 8:17 am
by Eric Pousse
Bonjour George,

Yes theoretically, the chamfer or the fillet must be on the side of the red line.
And you are right, it is not the case.
I think that it is a new bug...
Thanks, I will it.

Cordialement.

Re: Chamfer and Fillet

Posted: Fri Jan 08, 2021 5:27 pm
by Eric Pousse
OK George, I will post shortly a new beta to fix this problem.

A workaround is to draw the (red) line in attraction on the ends.

Re: Chamfer and Fillet

Posted: Sat Jan 09, 2021 11:18 am
by debenriver
Right – yes that works. And if you turn "Display Attraction names" on, it works from the centre/middle as well.

But on boat drawings, lines tend to be rather long – often a line drawn parallel to the centreline or datum waterline to construct other things, so the ends and even the centres are often a long way away! So cutting the lines is an easier option.

But it will be nice when you can fix it properly :D

Cheers -- George

Re: Chamfer and Fillet

Posted: Sun Jan 10, 2021 4:26 pm
by Eric Pousse
It is fixed : RealCADD 5.02b5

Thank you George.

Re: Chamfer and Fillet

Posted: Sun Jan 10, 2021 10:34 pm
by debenriver
Perfect :mrgreen:

Thanks Eric – makes life a lot easier!

George

Re: Chamfer and Fillet

Posted: Fri Jan 22, 2021 4:52 pm
by GeorgeK
Hello Eric

I have just bought and tried V 5.01. It is excellent.

I have the same difficulty with line direction and placement of chamfer/fillet. How may I get the fix for chamfer/fillet indicated in V 5.02b5? I don't see a way to update directly through application.

Regards, GeorgeK

Re: Chamfer and Fillet

Posted: Sat Jan 23, 2021 9:28 am
by Eric Pousse
Bonjour GeorgeK,

Thank you for your appreciation of RealCADD.
The last beta version is now b6.
You have to download it manually :RealCADD 5.02b6
It is a Mac version.
If you use RealCADD on Windows, say me.
There is no way to update RealCADD directly through the app.
Perhaps, I can add a check on the version number to inform the user that a new version is available.
But this will be active only for official version not beta versions.

Cordialement.

Re: Chamfer and Fillet

Posted: Sat Jan 23, 2021 6:33 pm
by GeorgeK
Thank you Eric.

I have a MAC but I prefer to use official version. I can manage placement of chamfer/fillet by setting up line directions in advance.

Do you plan to migrate the beta fix to the official version? If yes, can you provide an estimate of when?

Regards, GeorgeK

Re: Chamfer and Fillet

Posted: Sun Jan 24, 2021 10:36 am
by Eric Pousse
GeorgeK,

I will add the check of the version number and I update the official version.
Probably in one or two weeks.

Thanks